Category Archives: energy harvesting

Tiny Solar Energy Module (TSEM) Brings Big Performance

The Tiny Solar Energy Module (TSEM) by [Jasper Sikken] is not only physically tiny at one-inch square, but it is all about gathering tiny amounts of solar energy — amounts too small to be useful in a conventional sense — and getting meaningful work done, like charging a battery for later use. Elements that make this board easy to integrate into other projects include castellated vias, 1.8 V and 3.3 V regulated outputs that are active when the connected battery has a useful charge, and a low battery warning that informs the user of impending shutdown when the battery runs …read more

Continue reading

Posted in battery charger, charger, energy harvesting, lipo, pcb, solar, solar hacks, The Hackaday Prize | Leave a comment

PTPM Energy Scavenger Aims for Maintenance-Free Sensor Nodes

[Mile]’s PTPM Energy Scavenger takes the scavenging idea seriously and is designed to gather not only solar power but also energy from temperature differentials, vibrations, and magnetic induction. The idea is to make wireless sensor nodes that can be self-powered and require minimal maintenance. There’s more to the idea than simply doing away with batteries; if the devices are rugged and don’t need maintenance, they can be installed in locations that would otherwise be impractical or awkward. [Mile] says that goal is to reduce the most costly part of any supply chain: human labor.

The prototype is working well with …read more

Continue reading

Posted in battery, energy harvesting, generator, green hacks, LTC3331, magnetic induction, piezo, piezoelectric, power, recharge, rechargeable, selectable voltage, sensor, sensor node, solar, solar hacks, supercap, The Hackaday Prize, Thermal, thermoelectric, wireless | Leave a comment

Energy Harvesting Design Doesn’t Need Sleep

Every scrap of power is precious when it comes to power harvesting, and working with such designs usually means getting cozy with a microcontroller’s low-power tricks and sleep modes. But in the case of the Ultra Low Power Energy Harvester design by [bobricius], the attached microcontroller doesn’t need to worry about managing power at all — as long as it can finish its job fast enough.

The idea is to use solar energy to fill a capacitor, then turn on the microcontroller and let it run normally until the power runs out. As a result, a microcontroller may only have …read more

Continue reading

Posted in attiny85, bpw34, energy harvesting, Microcontrollers, photodiode, Power Harvesting, solar cell, solar hacks, solar power, The Hackaday Prize | Leave a comment

SPINES Design Makes for Modular Energy Harvesting

The SPINES (Self-Powered IoT Node for Environmental Sensing) Mote is a wireless IoT environmental sensor, but don’t let the neatly packed single PCB fool you into thinking it’s not hackable. [Macro Yau] specifically designed SPINES to be highly modular in order to make designing an energy harvesting sensor node an easier task. The way [Macro] sees it, there are two big hurdles to development: one is the energy harvesting itself, and the other is the software required to manage the use of every precious joule of that harvested energy.

[Macro] designed the single board SPINES Mote in a way that …read more

Continue reading

Posted in energy harvesting, IoT, Power Harvesting, sensor node, solar, solar hacks, SPINES, The Hackaday Prize, wireless | Leave a comment

Ultra-Low Power, Energy Harvesting Battery Charger

This half-inch square ultra-low power energy harvesting LiPo cell charger by [Kris Winer] uses a low voltage solar panel to top up a small lithium-polymer cell, which together can be used as the sole power source for projects. It’s handy enough that [Kris] uses them for his own projects and offers them for sale to fellow hackers. It’s also his entry into the Power Harvesting Challenge of the Hackaday Prize.

The board is essentially a breakout board for the Texas Instrument BQ25504, configured to charge and maintain a single lithium-polymer cell. The BQ25504 is an integrated part that takes care …read more

Continue reading

Posted in battery charger, BQ25504, charger, energy harvesting, lipo, low power, SensorTile, solar, solar hacks, The Hackaday Prize | Leave a comment

A Flashlight Powered by Your Hot Little Hands

We are smack-dab in the middle of our Energy Harvesting Challenge, and [wasimashu] might have this one in the palm of his hand. Imagine a compact flashlight that doesn’t need batteries or bulbs. You’d buy a 10-pack and stash them everywhere, right? If there’s nothing that will leak or break or expire in your lifetime, why not have a bunch of them around?

Infinity uses nothing but body heat to power a single white LED. It only needs a five-degree temperature difference between the air and your hand to work, so it should be good in pretty much any environment. …read more

Continue reading

Posted in boost converter, energy harvesting, human batteries, peltier, peltier unit, The Hackaday Prize | Leave a comment